Do you find yourself hunting for information on A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't precisely brain surgery, however it does require solid plumbing, carpentry, as well as often, tiling skills. Changing an old bathtub with a new one is likewise a moderately difficult project. If the old tub is easily easily accessible, the task can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old bathtub and also embeded in the new one. See to it you have actually qualified yourself for the job and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This write-up will certainly assist you set up a brand-new tub in your restroom if you have currently gotten a brand-new bathtub and do not require to alter the plan of your previous water system pipes.
Your devices and also product checklist ought to comprise the following:
- New Bathtub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Chisel
- Tape Measure
- Pipe Caps
Planning for the Installment
To start with, the supporting structure provided with the bathroom should be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before carrying on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, place the bath tub in the called for placement. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bath tub until the level reviews degree.
To install taps, fit all-time low of the outermost flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Turn on the supply of water and inspect all joints and also new pipework for leakages as well as tighten them if required. Fill the tub as well as likewise inspect the overflow electrical outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the maker's instruction manual. Tiling as well as securing around the tub should wait till the bathtub has actually been utilized a minimum of once as this will resolve it right into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in place in between the tap as well as the sink. Protect the faucet in position with the producer provided backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind should be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, creating the water to pass through the wall surface between the bath and also the tiling, causing difficulties with wetness and feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealant can split fairly early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof sticky as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
- Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.
- Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.
- Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.
- Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.
- Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.
- If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
I ran across that entry on A Step-by-Step Guide to Installing a Bathtub while surfing around the web. Do you know somebody else who is inquisitive about the subject? Do not hesitate to promote it. Thanks a lot for your time invested reading it.
Free Estimates
Comments on “DIY Tub Installation.”